Advantix Vario shower channel standing grate, wall
Product information
Advantix Vario shower channel standing grate, wall
for Advantix Vario shower channel base unit, wall model 4967.10, 4968.10
| Year built (from): | 18.1.2016 |
Trade mark rights exist for this document; for further information, go to viega.com/legal .
Target groups
The information in this instruction manual is directed at the following groups of people:
Heating and plumbing experts and trained personnel
SHK-Fachkräfte
Individuals without the abovementioned training or qualification are not permitted to mount, install and, if required, maintain this product. This restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with the general rules of engineering and the Viega instructions for use.
Labelling of notes
Warning and advisory texts are set aside from the remainder of the text and are labelled with the relevant pictographs.
DANGER!
This symbol warns of possible life-threatening injury.
WARNING!
This symbol warns of possible serious injury.
CAUTION!
This symbol warns of possible injury.
NOTICE!
This symbol warns of possible damage to property.
INFO!
This symbol gives additional information and hints.
About this translated version
This instruction for use contains important information about the choice of product or system, assembly and commissioning as well as intended use and, if required, maintenance measures. The information about the products, their properties and application technology are based on the current standards in Europe (e.g. EN) and/or in Germany (e.g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/Germany. These should serve as recommendations in the absence of corresponding national regulations. The relevant national laws, standards, regulations, directives and other technical provisions take priority over the German/European directives specified in this manual: The information herein is not binding for other countries and regions; as said above, they should be understood as a recommendation.
Other applicable documents
This instruction for use describes the mounting of an accessory set for an Advantix Vario shower channel in rough steps.
INFO!
The instructions for use of the Advantix Vario shower channel must also be strictly observed for the mounting of the accessory set.
Product description
The standing grate set may be mounted only in Viega Advantix Vario shower channel base units, wall model 4967.10 and 4968.10.
Model |
|---|
Article |
Description |
4967.31 |
736 576 |
Advantix Vario standing grate |
Overview
- 1 Standing grate
- 2 Standing grade support
- 3 Standing grate holder
- 4 Cover caps
- 5 Standing grate insert
- 6 Mounting tool
Handling
Missing Title
Installation dimensions
Assembly
-
Remove the site protection inserts.
-
Fit the sieve insert in the area of the drain hole.
-
Assembly example on left-hand side: Push the standing grate holder onto the mounting tool.
-
Mount the standing grate holder on the tile edge profile using the mounting tool.
-
Push the grate holder until it is 10 mm away from the tile surface.
-
Push the grate holder until it is 10 mm away from the tile surface.
-
Check that the standing grate holder is correctly positioned.
-
Determine the length to be cut off.
X = length to be shortened
-
Cut off length X.
-
Insert the standing grade support.
-
Push the standing grate support onto the mounting tool.
Select the standing grate support length from the list:
Standing grate support A at surface height (tiles and adhesive) 10‑16 mm
Standing grate support B at surface height (tiles and adhesive) 15‑23 mm
Standing grate support C at surface height (tiles and adhesive) 23‑28 mm
-
Mount the standing grate support on the tile edge profile using the mounting tool.
-
Check the standing grate support is correctly positioned.
-
Distribute the supports evenly.
-
Determine the standing grate length.
-
Shorten and deburr the standing grate.
NOTICE!The standing grate must not be shortened with a cutting disc (angle grinder).
If required, shorten the standing grate with a handsaw and deburr.
-
Insert the standing grate.
-
Press the cover caps on.
Care
NOTICE!
Risk of damage due to unsuitable cleaning agent.
The following cleaning agents can damage chrome-plated surfaces and therefore may not be used:
scouring agent
abrasive sponges
lime, plaster or cement dissolver
solvents or other acidic cleaning agents
Normal soap or a mild cleaning agent can be used for regular care and prevention of lime scale. Under no circumstances should scouring agent or scratching objects be used.
Strong stains, even around the drain unit and the siphon, can be removed using typical household cleaner. Please note that the cleaning agent must be rinsed off thoroughly with clear water after the prescribed soaking time. There should be no residue on the components.
Disposal
Separate the product and packaging materials (e. g. paper, metal, plastic or non-ferrous metals) and dispose of in accordance with valid national legal requirements.