Care for Viega system press tools
Trade mark rights exist for this document; for further information, go to.
The information in this instruction manual is directed at the following groups of people:
Heating and plumbing experts and trained personnel
Individuals without the abovementioned training or qualification are not permitted to mount, install and, if required, maintain this product. This restriction does not extend to possible operating instructions.
The use of Viega products must be carried out in accordance with the general rules of engineering and the Viega instructions for use.
Warning and advisory texts are set aside from the remainder of the text and are labelled with the relevant pictographs.
This symbol warns of possible life-threatening injury.
This symbol warns of possible serious injury.
This symbol warns of possible injury.
This symbol warns of possible damage to property.
This symbol gives additional information and hints.
This instruction for use contains important information about the choice of product or system, assembly and commissioning as well as intended use and, if required, maintenance measures. The information about the products, their properties and application technology are based on the current standards in Europe (e.g. EN) and/or in Germany (e.g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/Germany. These should serve as recommendations in the absence of corresponding national regulations. The relevant national laws, standards, regulations, directives and other technical provisions take priority over the German/European directives specified in this manual: The information herein is not binding for other countries and regions; as said above, they should be understood as a recommendation.
Viega system press tools have been specifically designed for and adapted to the installation of the Viega press connector systems. If systems by other manufacturers are used, Viega cannot provide any warranties.
Please fulfil your duty of care and follow these care instructions. In this way, you achieve maximum functional safety between the maintenance intervals. The general principle "safety through maintenance" applies. If the advice is not followed, no responsibility for personal injury can be accepted.
2299.2, 2299.4, 2299.41, 2299.6, 2299.62, 2299.7, 2299.8, 2299.81, 2299.9, 2484.7, 2484.9, 2489.9, 2799.7, 4284.9, 4299.95384.7, 5399.7
2296.1, 2296.4, 2496.3, 2496.5, 5396.1
9696.1, 9696.6, 9696.7
Clean the press tools after use and lightly oil.
Store the press tools in a clean and dry place.
During transport, protect the press tools from mechanical influences.
For trouble-free operation, perform checks in regular intervals:
After every use, check the press contour of the press jaws, press chains and press rings as well as the ball heads of the hinged adapter jaws and the contact points of the press rings for damage or visible wear.
Check the press jaws and press rings for smooth operation.
Carry out a test pressing with the press connector inserted, and check the pressing point for formation of burrs.
In case of malfunctions, contact an authorised service partner.
Application and care should be carried out by specialists in compliance with the servicing intervals.
Regularly clean the press contours of the press jaws, press rings and press chains with fine steel wool or cleaning fleece in order to remove deposits and prevent corrosion (e.g. using the Viega cleaning fleece, art. no. 104 412).
Apply maintenance oil to the hinges and all moving parts (art. no. 667 924). Move the tools and joints while lubricating them.
Note the pictures in chapter.
Then thinly spray the press jaw or press ring with maintenance oil (art. no. 667 924) and let it work for a short time before wiping off with a lint-free cloth.
Every two years, have an authorised service partner (see) carry out the maintenance.
Lubrication points at a press jaw.
Lubrication points at a press ring.
Lubrication points at press machines.
Lubrication points at the press ring Geopress K.
Lubrication points at a hinged adapter jaw Z2.
Lubrication points at Press Booster (hinged adapter jaw Z3).
Lubrication points on the ball heads.
Use paste Molykote G-n Plus (art. no. 794 910).
Lubrication points at the press ring drive.
Lubrication points at the press-in tool.
Viega recommends to have the system press jaws, chains, and rings regularly by a service partner. During the procedure, wear parts are replaced, press jaw contours are revised and the system press jaws, chains and rings are reset.
The Viega system press jaws and system press rings have a label showing the date when the next maintenance is due. Respect the maintenance dates in order to guarantee safety and proper function. After completed maintenance, the Viega service partner will apply a new sticker.
For maintenance and repair of the press tools, contact the service partner in your country.
König & Landl GmbH
Gewerbering 2, 2020 Hollabrunn
https://www.koenig-landl.at / email@example.com
+43 (01) 479 74 84‑50 / +43 (01) 479 74 84‑55
Nepean Boltmaster Pty Ltd ABN
42 Borec Road, 2750 Penrith
+61 (2) 4722 3034 /firstname.lastname@example.org
Allied Power Tools Pty. Ltd.
12/76 Rushdale St, Knoxfield, VIC 3180
+61 (3) 9764 email@example.com
Grote Steenweg 116, 3454 Rummen-Geetbets
+32 (11) 58 43 50 /firstname.lastname@example.org
无锡市锡山区万全路 30 号平谦国际现代产业园 P 栋
400 0688 668/Dong.email@example.com
Viega (China) Plumbing Systems Co., Ltd.
Building P, Pingqian International Modern Industrial Park, No. 30 Wanquan Road, Xishan District, Wuxi, China (214107)
400 0688 668/Dong.firstname.lastname@example.org
CZ / SK
Mátl & Bula, spol. s r.o.
Stará pošta 750, 664 61 Rajhrad u Brna
+420 547 424 424 /email@example.com
Hans-Joachim Voigt & Sohn
Nordlichtstrasse 48/50, 13405 Berlin
+49 (30) 413 4041 /firstname.lastname@example.org
Billwerder Billdeich 601c, 21033 Hamburg
+49 (40) 7511 900 /Service@HHHydraulik.com
Hamburger-Hochdruck-Hydraulik GmbH – Süd
Neue Gautinger Str. 21, 82110 Germering,
+49 (89) 130 111 03 /Service@HHHydraulik.com
Scherer`s Elektro ApS
Resenbrovej 4, 2610 Rodovre
+45 (44) 843738 /Steffen@scherers-elektro.dk
Tecno Izquierdo S.L.
Avda. del Manzanares 222, 28026 Madrid
+34 (914) 759158 /email@example.com
245 boulevard de l'Europe, 62118 Monchy-le-Preux
+33 (361) 47 40 45 /firstname.lastname@example.org
Sähköhuolto Tissari Oy
Poijutie 3, 70460 Kuopio
+ 358 (17) 26 48 500 /email@example.com
Ergon Equipment A.E.T.E.
102 Kleisthenous & Papafiessa Str, 153 44 Athens
+30 (210) 604945 4 /firstname.lastname@example.org
Via Artigianale Nord, 6, 39044 Neumarkt
+39 (0471) 813399 /email@example.com
Via Sassonia, 16/G, 47900 Rimini
+39 (0541) 741003 /firstname.lastname@example.org
Toyo Kiko Inc.
717‑5 Shimokuya-machi, 378‑0061 Numata-shi
+81 (278) 24 41 77 /email@example.com
Grønvold Maskinservice A/S
Brobekkveien 104 A, 0613 Oslo
+47 (23) 05 06 40 /Terje@gronvoldmaskin.no
Canadabaan 2, 5388 RT Nistelrode
+31 (412) 617 299 /firstname.lastname@example.org
Московская область, Солнечногорский район, Ленинградское шоссе, 34 км., стр. 15 (полигон МАДИ)
+7 (499) 702‑45-88 / email@example.com
Elektroverkstaden Kent Andersson AB
Propellervägen 7, 39241 Kalmar
+46 (732) 30 57 firstname.lastname@example.org
MEP LLA Glasgow - Depot 190
Unit K, Ashley Drive Bothwell, G71 8BS Glasgow
+44 (1698) 740047 /email@example.com
Broughton Plant Hire
Unit 10, Trade City, Ashton Road, RM3 8UJ Romford, Essex
+44 (1708) 383350 /firstname.lastname@example.org
Separate the product and packaging materials (e. g. paper, metal, plastic or non-ferrous metals) and dispose of in accordance with valid national legal requirements.